installing metal soffit on gable ends
Install the lowest fascia on the gable end first. Cap the bottom of the board and run the soffit up to it.
Vinyl Siding Vinyl Siding Vinyl Siding Installation Vinyl Siding Repair
Lap screws should be placed 12 on center hitting the high seam of roofing corrugation.
. GABLE END SOFFIT PANELS - Start at the base of the gable end and work up to the peak from each side as far as full panels will fit. Overlap the ends a minimum of 6 See illustration 1. Start at one corner of your house and work your way around using the drill or electric screwdriver to drive one wood screw twice as long as the material is thick through the soffit material and into the gable at each corner of the piece and one in the middle.
Cut a tapered piece of wood so the bottom of the eave is even with the board. Color Guide Panel J-Channel Fascia sizes vary Pancake Screw Wood Screw. Check roof for squareness by making a 3 line across the eaves.
Com-pleting the 3 x 4 x 5 right angle triangle should place the 4 edge or the 3 edge of the triangle parallel with the gable. Fasten gable trim with ¼ x ⅞ Inch metal to metal lap screws. Nailing strips may be required.
Remove enough of the fascia lip to cover returns then nail them in place and cut the ends off flush with eave ends. FINISH TRIM - Use drip edge or all-purpose trim to cover and finish top edge of fascia trim. Same Day Response Free Quotes.
- Measure one panel width in from the gable end and run a chalk line from the eave to the ridge. Browse Get Results Instantly. Place an alignment line along the gable end where the first roof panel will be installed.
Cover balance of gable end with fascia trim and cut to make overlap joint at peak. Allow each consecu-tive course to overlap the previous one 3 inches. Channel nail and install along the entire length of the wall surfaces and up to gable peak on side wall 2.
Do not place screws 12 from the ridge of the roof until ridge cap is installed. 3 Install Fascia Trim over end capping the end of the shingles and going up the fascia and fastening with Wood Screws. Place a piece of hardi siding on the wall at the right height above the piece below and slide it towards the gable until it touches the gable.
Slide panels into channel and secure into position using nails in panel grooves as required to under edge of fascia board. - An overhang of 1 at the eave is recommended. Ad Top New York Soffit Fascia Installation Services.
No Job is Too Big or Too Small. - At the Gable ends extend the sheet 1 beyond the gable fascia unless you are using a Gable Trim in which case the sheet should be flush. SmartAnswersOnline Can Help You Find Multiples Results Within Seconds.
Metal soffit is installed in much the same manner. Install a soffit double-channel lineal or H-bar. Find The Right Independent Professionals To Complete Your Home Improvement Project.
Measure the distance from the bottom of the piece to the gable. Ad Hire The Right Contractor To Help With Your Home Improvement Project. Additional screws should be placed 12 on face staggered from top screws.
Now measure the height the siding needs to be until the angle starts. Ad Search For Info About Metal roofing standing seam installation. Areas of underlayment that have torn should be replaced or repaired prior to installation of the metal roof.
It may be necessary to cut. To turn a corner measure from the channel at the wall corner to the channel at the corner of the fascia board subtract 14-inch for expansion. 2 Install Soffit Panels either horizontally or vertically tucking them inside the J-Channel.
Miter the soffit panels to fit into the H-bar or lineal channel. For installation begin at the eave and roll the underlayment horizontally parallel to the eave. SOFFIT PANELS - gable end - Start installation at the base of the gable end working up to the peak as far as full panels will fit.
If installing soffit panels over existing wood soffits soffit J channel can be used in place of frieze runner. Slide panels into channel and secure to under edge of fascia board. Either bend or clip the bottom tip flush with the bottom of the soffit.
No Job is Too Big or Too Small. Each piece of 4-foot length should have a minimum of 6 screws in it.
Pin By Brian Rogers On Soffit Repair Porch Design Exterior Remodel Roof Soffits
Gable End Eave Design Exterior Trim Building A House Design
Soffit House Exterior Vinyl Siding Installation Home Construction
Attic Renovation Attic Remodel Attic Playroom
Aluminum Soffit Fascia Installation Hicksville Ohio Soffit Ideas Vinyl Siding Installation Home Building Tips
12 How To Birdbox Soffit And Fascia Youtube Order Of Operations Fascia Teaching
How To Build A Soffit Box Youtube Diy Roofing House Paint Exterior Vinyl Soffit
Building Green Homes Step 6 Drying In The Roof Metal Roof Installation Metal Roof Roof Installation
Diagram Soffit Fascia Guttering Door And Window Repairs Pvc Doors And Windows In Ireland Longford Westmeath Leitrim M Framing Construction Fascia Window Repair
Pin On Roof Details
Roof Soffits Roof Sheathing Roof Framing
How To Install Aluminum Soffits That Are Maintenance Free Roofing Installing Siding Roof Edge
How To Install Soffit Vinyl Soffit Vinyl Siding Installation Porch Design
Installing Soffit On Top Of Previously Existing Soffit Uses J Channel To Support The New Soffit Home Construction Roof Construction Home Remodeling
How To Install Aluminum Soffits That Are Maintenance Free Roofing Corrugated Metal Roof Roof Edge
Metal Roof Trim Metal Roof Roof Trim Vinyl Siding Installation
Follow These Recommendations To Save Money And Time When Installing Soffit Install The Soffit Exterior House Siding House Exterior Installing Siding
Aluminum Fascia Trim Google Search House Paint Exterior Vinyl Soffit Vinyl Siding Installation
How To Install Aluminum Soffits That Are Maintenance Free Vinyl Soffit Roof Soffits Roof Edge